Apakah suhu pengeringan untuk gegelung digulung sejuk-?

Mar 24, 2026 Tinggalkan pesanan

1. Apakah julat suhu yang sesuai untuk pengeringan gegelung digulung sejuk?

Bahagian pengeringan pada talian pembersihan keluli digulung sejuk biasanya menggunakan pengeringan udara panas atau pemanasan induksi elektromagnet. Tetapan suhu bergantung pada spesifikasi jalur dan kelajuan talian pengeluaran.

Secara amnya, suhu pengeringan (suhu udara panas) disyorkan untuk dikawal antara 80 darjah dan 120 darjah, dan suhu jalur (suhu jalur sebenar) apabila keluar dari ketuhar pengeringan harus mencapai 60 darjah hingga 90 darjah.

cold-rolled coil

2. Masalah kualiti apa yang boleh timbul daripada tetapan suhu pengeringan yang tidak betul?

Suhu Rendah (Pengeringan Tidak Mencukupi):

Kelembapan Tersisa: Pengeringan permukaan jalur yang tidak lengkap meninggalkan sisa kelembapan selepas penggulungan, yang menyebabkan kesan air atau karat kuning.

Kecacatan Pengegangan: Kelembapan menguap apabila memasuki ketuhar pengewangan, berpotensi menyebabkan turun naik atmosfera dan bahkan risiko perubahan warna akibat pengoksidaan atau kerapuhan hidrogen.

Pengurangan Lekatan Salutan: Untuk produk yang memerlukan pengminyakan atau penyaduran seterusnya, kelembapan baki melemahkan lekatan salutan.

Suhu Tinggi (Pengeringan Melebihi -):

Kekusaman Oksidasi: Suhu tinggi menyebabkan permukaan jalur bersentuhan dengan oksigen, membentuk filem oksida coklat kebiruan-, yang menjejaskan penampilan dan prestasi pemprosesan seterusnya.

Perubahan dalam Sifat Mekanikal: Bagi keluli tolok nipis atau berkuat tinggi, suhu yang terlalu tinggi boleh menyebabkan pengerasan akibat usia atau turun naik luarbiasa dalam kekuatan hasil.

Kegagalan Salutan Minyak: Jika minyak pencegah karat- digunakan sejurus selepas pengeringan, suhu jaluran yang tinggi boleh menyebabkan filem minyak itu menguap atau teroksida, sekali gus mengurangkan kesan pencegah karat-nya.

Pembaziran Tenaga: Pemanasan berlebihan meningkatkan penggunaan tenaga dan mempercepat penuaan peralatan.

cold-rolled coil

3.What are the main factors that affect the setting of drying temperature?

Strip thickness and heat capacity: Thicker strips have higher heat capacity and slower heating, requiring higher hot air temperatures or longer drying times; thinner strips heat up quickly, but excessively high temperatures can cause overheating.

Production line speed: Higher speeds mean shorter strip time in the drying section, necessitating higher temperatures or longer drying sections to ensure sufficient heat input.

Inlet strip moisture content: The residual water content on the strip surface after rinsing is affected by the rinsing method and the condition of the squeeze rollers. If the squeeze rollers are worn or under insufficient pressure, the strip will have a high water content, requiring a higher drying temperature.

If the subsequent process is annealing, drying only needs to ensure no water is present, and the temperature should be relatively low.

If the subsequent process is oiling, the strip exiting the drying oven temperature must be controlled <=50℃ to prevent oil evaporation.

If the subsequent process is galvanizing, the drying temperature must be matched with the pre-galvanizing heating section.

Drying equipment type: Hot air drying has relatively low efficiency and high temperature requirements; electromagnetic induction drying has high efficiency and rapid heating, allowing for the setting of lower hot air auxiliary temperatures.

cold-rolled coil

4.Are there different requirements for drying temperature for different product types?

Ordinary cold-rolled coil (CQ): The primary goal is to ensure complete drying, with some fluctuation allowed, and cost is the priority.

Automotive outer panels (O5): Strictly control the upper limit to prevent oxidation color and surface quality damage. Some production lines adopt a low temperature + extended drying time strategy.

Silicon steel (electrical steel): The insulating coating on the surface of silicon steel is sensitive to moisture and needs to be thoroughly dried. At the same time, high temperature should be avoided to prevent damage to the coating performance. Electromagnetic induction drying is often used to precisely control the temperature.

Galvanized substrate: It needs to be connected with the temperature of the pre-plating heating furnace to avoid sudden temperature changes that cause fluctuations in the shape of the strip and to prevent a decrease in the adhesion of the zinc layer.

 

5.How can drying temperature be effectively monitored and managed during production?

**Strip Temperature Meter:** An infrared thermometer is installed at the dryer oven outlet to monitor the actual strip temperature in real time. This is the most direct feedback parameter.

**Hot Air Temperature:** Monitor the hot air temperature in each zone of the dryer oven to ensure the heating system is functioning properly.

**Speed ​​Linkage:** PLC-linked control of drying temperature and production line speed-automatically adjusting hot air temperature or fan frequency when speed changes to maintain stable heat input.

Check the condition of the squeeze rollers every shift to ensure minimal water content in the incoming strip.

Check for blockages in the dryer oven nozzles to ensure even hot air coverage across the strip width.

Observe the strip surface after exiting the dryer for residual steam or oxidation and adjust accordingly.

**Low Strip Temperature:** Check the hot air temperature setting, fan speed, production line speed for excessive speed, and whether the squeeze rollers are malfunctioning.

**High Strip Temperature:** Check for temperature sensor drift, heating system malfunction, and abnormal speed reduction.